TEXT MODE CENTOS 7

install CentOS in a text mode, you can only use the default partition scheme described in this section. Partition or the file system you cannot add or remove beyond the installer will automatically add or remove.

1, Special and network disk(Specialized & Network Disks)

On this screen, you can see the storage devices available on the local computer. You can click the "add disk" button to add extra special or network equipment.

2, Automatic configuration partition(Automatically configure partitioning)

Automatic partition recommendations, if you are doing a clean install of previously unused storage or need not let may exist in any data storage. By this way, leaving the default option to auto configure partition radio button, let the installer on your storage space, create the necessary partition.

3, I wanted the extra space used(I would like to make additional space available)

To automatically partition, you can also choose to "I want to make more space available" check box to choose how to redistribute other file system space. If you choose to automatically partition, but not enough storage space to complete the installation, click the Done (complete), a dialog box appears.

4, Our data encryption(Encrypt my data)

In the encryption part, you can choose to encrypt my data check box, except all partitions to encrypt / boot partition.

5, Abstract the complete disk and boot program(Full disk summary and bootloader)

At the bottom of the screen, is your configuration on the boot loader will be installed overall summary button on the disk and boot loader.

(2)Manual partitioning(Manual Partitioning)

When you click the install target, if you choose"IToThe configuration partition(I will configure partitioning)"Option to manually partition screen. On this screen configuration disk partition and the mount point.

Manual partitioning screen function initially in the mounting points on the left side of a single pane. The panel is empty, but about creating a mount point, also shows the installer detection point of the existing installation. The loading point is detected operating system installation held. Therefore, if a partition is shared between several devices some file systems may show many times. In the selection of the total storage space and available space will show this pane below.

1, Add a file system and the partition configuration

Add a file system is a process of two steps. First create a specific partitioning scheme of the mount point. The mount point will appear in the left pane. Next, you can use in the right pane, you can select a name, in which the device type, the type of file system, label options to customize, and whether it is encrypted or reformat the corresponding partition.

For each manually create a new mount point can be set from the partition scheme, located in the left pane of the drop-down menu. The options available are standard partitioning, BTRFS, LVM and LVM reduced configuration. Need to pay attention to is / boot partition will always be in a standard partitioning, regardless of the choice of value in this menu.

In addition, created using the "+" button at the bottom of each panel mount point. Add a mount point new dialog box, and then open the. Both the choice of default from the mounting point of the drop-down menu path or type your own - for example, select / root / boot partition or boot partition. Then enter the partition size, the use of ordinary sized units, such as MB, GB or TB, the capacity of text field - need for example, type 2GB to create a 2G partition. If the field blank, or if you specify the size greater than the available space, all the remaining available space will be used. After entering the details, click "add a mount point" button to create partition.

To customize a partition or volume, select the mount point and the following function in the left pane, and then appear on the right:

Name(Name): Assign a name, a LVM or to Btrfs. Need to pay attention to is the standard partition automatically named and their names cannot be edited when created, such as a / home is assigned the name SDA1.

The mount point(Mount point): Enter the partition mounted. For example, if the partition is the root partition, input / into / boot /; boot partition, and so on. For a swap partition, set up - set the type of file system mount point should not, it is enough to exchange.

Label(Label): To assign a label partitions. Tag is used to allow you to easily identify and solve a single partition.

The required capacity(Desired capacity): The size of the required partition. You can use an ordinary sized units, such as kilobytes, megabytes, GB or TB. Zhao is the default option, if you do not specify any unit.

The device type(Device type): The standard partition, BTRFS, LVM or LVM streamlined configuration choice between. If selected for separating two or more disks, RAID will also be available. Check the adjacent frame partition encryption, encryption. The system will prompt you for your password after setup.

The following is a brief description of the types of equipment, and how they are used:

Standard: Standard partition partition may include a file system or swap space, also can provide a container for the software, RAID and LVM physical volume.

Logical volume (LVM): create a LVM partition to automatically generate an LVM logical volume. LVM can be used in the physical disk, improve performance.